Bosch Table Saw Miter Slot

11-05-2021
 |  [RAND-100] - Comments


Make an adjustable miter bar. Some tablesaw jigs, such as cutoff sleds, ride in the saw's miter slots, and a well-fitting miter bar keeps these jigs accurate. You can make your own miter bar out of hardwood, but it's tricky to get—and maintain—that good fit. About 1 ⁄ 64' narrower than your saw’s miter slot. Worksite table saw – features 15 Amp saw delivers 4.0 Max HP and 3,650 RPM, for the power required for ripping rip-cutting and cross-cutting in of fine- and rough-carpentry materials Large cast aluminum top – provides increased work space and material support with a 25 In. Ripping capacity to cover all typical jobsite rip-cutting widths.

Introduction

The DeWalt DWE7480 is the one of the new range of saws, recently released by DeWalt. in fact it is an upgrade and set to replace the very popular DW745, which has been a solid performer for company. The DW745 ticked a lot of boxes for wood workers and tradesmen, which is why it has always received great reviews, because it was and still is a great, well made product. Ultimately, all us wood workers want from the table saw that we choose, is something that is constructed well, sets easily and cuts accurately again and again and again. And all the time DeWalt keep churning out great table saws, we’ll keep buying them.

You may see references to DWE7480 and the DWE7480XA. These saws are exactly the same the “XA” refers to the version of the saw that comes with the their heavy duty scissor stand that folds flat for storage and transportation. I would have to recommend the version with the stand as their is only approximately $20 difference between the two

Now lets get back to the task at hand. DeWalt have tried to address some of the few shortcomings of the DW745. For some they have succeeded, and for some they haven’t (psst!! better saw blade please).

Specification

Amps15.0Amps
HorsepowerHP
No Load Speed4800rpm
Blade Diameter10″
Arbor Size5/8″
Dust Port Diameter2-1/2″
Depth of Cut at 90°3-1/8″
Depth of Cut at 45°2-1/4″
Max Rip To Right Of Blade24″
Max Rip To Left Of Blade12″
Max Width of DadoN/A”
Tool Weight48lbs
Shipping Weight57lbs

Size and Weight

As you would expect from a portable table saw. The DeWalt comes in at a very respectable 48lbs,(the weight without the stand) which is only 3lbs heavier than its predecessor the DW745. It has a very compact table size of 22″ x 23″. The only table saw smaller in this class of table saws is the Bosch GTS1031. However, the DWE740 does come with a wider rip capacity which is great news for anyone who works with full size sheet materials. The is achieved with a telescopic fence that t extends to give a rip capacity of 24″ which enables you to rip a full size sheet of ply in half.

The Scissor stand that is available with DWE7480XA version of this saw is strong and sturdy and brilliantly simple. OK, so it doesn’t isn’t the type of clever engineering that we have seen with Bosch’s Gravity Rise Stand on the 4100-09, or the barrow style stand found on the SawStop JSS-MCA. But for $20 its an absolute bargain.

So when it comes to portability, this saw is a winner. One of the lightest and smallest table saws around today.

Blades and Dado’s

Its a common complaint that the blade that comes with most table saws are through away rubbish. And the DWE7480 is no exception. Its a 24 tooth 10″ blade. Its lacks the lazer cut resonance slits and has small carbide teeth but it is factory sharp and does the job of ripping well.But I’m going to cut DeWalt a lot of slack here. We have to remember that DeWalt have produced a sub $400 table saw here. So when it gets dull, toss it and get one of the great quality after market blades that are available. Something like this Freud Blade

Now I’m afraid to say that you won’t be able to use a dado blade with this saw, this is due to the shaft on this saw not being long enough to accommodate it. If this is something that you really need from a saw. I would have a closer look at the Bosch GTS1031 This is capable of cutting 1/2″ dado’s. I have heard some people managed to get 5/8″, but this is the absolute maximum. It seems the widest dado you can get on this class of saws in the 13/16″. If you need this capacity I would be looking at the DeWalt DWE7490X.

The Max depth of cut at 90 and 45 degrees is 3-1/8″ and 2-1/4. This is pretty standard for saws portable table saws.

Fence & Miter

It comes with a the same rack and pinion telescopic fence system that was also very popular on the DW745. This lets you quickly and accurately set the blade over and over again. It glides smoothly on the measuring rail and locks perfectly square to the blade. Its a great system that works well. It can also be found on DeWalt DWE7490X, DWE7499GD

The saw comes with a standard square miter slot (unlike the T-Style found on the Bosch GTS1031) and a pretty standard miter gauge.

Motor

The motor is an area that has been improved with the DWE7480, Just like the DW745, It is powerful enough to handle hardwoods. It has a max RPM of 4800 which is faster than the DW745 which spins at 3850RPM. The DWE7480, as with all table saws in the portable category, they tend to use a 15 amp direct drive brush motor which has the benefits of being light but the disadvantage of being loud. The closest contender to this saw when it comes to the motor is the Bosch GTS1031

Safety

The DWE7480 comes with DeWalts ITE PRO Modular Guarding System. It’s a tool-less blade guard system consisting of a rise and fall riving knife, blade guard and anti-kickback pawls. It can be assembled and disassembled in a approximately 30 seconds.

Summary

DeWalt have done a amazing job with the DWE7480. It has really tried to learn from feedback on its predecessor and this is evident with the upgraded motor and the ability to rip full size sheet materials. Its rugged design and fast and accurate fence make this a great choice for the woodworker or tradesman who needs the portability of a site saw. This saw is amazing value. For less than $400 you get a small, light table saw. It has a powerful motor, cuts full size sheet materials, Has a brilliant fence system and a very safe modular blade guard and riving knife system.

You can read more about this saw on the DeWalt website

Here is a great video from the ConcordCarpenter where he looks at the DeWalt DWE7480

Permalink Reply by kevin reed on May 31, 2010 at 3:13pm
your'e a hardcore woodworker Mr waller. If i had to do that much to use my tools they would get very little work. i am also in the market for a portable table saw. those two are on the top of my list.
Permalink Reply by Don Clark on May 31, 2010 at 4:11pm
When I was looking to upgrade my saw a few months back the Bosch was on my short list of candidates ( the other was the Rigid TS3650/3660, I need movable but not necessarily portable) due to the outstanding reviews on various woodworking sites. I ended up finding a deal on a slightly used TS3660 so I went that way, so I can't quite comment on the bearing reports on the Bosch.
Fine Woodworking did a review of 6 portables in their 2010 Tools & Shops Annual issue and they didn't make any mention of the miter slots on the Makita, and they seemed to hit on most of the quirks for the individual saws. If, however, you have found something different about the slots, then that would be a deal-breaker in my book if you want to use an aftermarket gauge. The Bosch got their top marks overall, with the Rigid R4510 coming in a close second.
Permalink Reply by David Dean on May 31, 2010 at 4:17pm
Will Stanley I know you all are talking about a small table saw I have been working on the same saw for the last 5 years and the top is 20' x 15' and my saw was made in 1965 by cratfsmen it is hrad to get any big stuff it to cut and room being what it is but in the long run you whod be batter off getting a bigger table saw
Permalink Reply by Bernie Hall on June 1, 2010 at 7:38pm
I also am limited in space (10x16). Based on the specs, reviews, video on YouTube, and Bosch's reputation I decided on the Bosch 4100 with the gravity rise stand (bought in Sept 08). I must admit I have not heard anything about a wiring or bearing issue. I have had no problems with this saw.
This is a first class, well engineered, well built saw. All the critical adjustments (blade vertical, parallel to mitre slot, fence parallel to blade, etc) were dead-on right out of the box. I installed a Freud thin kerf blade with stabilizing plate (highly recommend a thin kerf blade). I bought the side and back extensions which greatly increase the usability of the saw. Even though the miter slot is a T-slot, it accepts 3rd party accessories.
The stand is a beautifully engineered device. I don't anticipate taking this around a lot like a contractor, but I sure do like that I can fold it up and stick it in the corner when not in use and gain some space back. I am very impressed and pleased with this saw and easily recommend it.
Permalink Reply by Phil Howard on June 1, 2010 at 11:44pm
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).
Permalink Reply by Stanley C. Pearse on June 2, 2010 at 2:53pm
Thanks Bernie for your comments.
One question...has there been any issue using the thn kerf blade and the riving knife?
Thanks again!!
Stan
Bernie Hall said:
I also am limited in space (10x16). Based on the specs, reviews, video on YouTube, and Bosch's reputation I decided on the Bosch 4100 with the gravity rise stand (bought in Sept 08). I must admit I have not heard anything about a wiring or bearing issue. I have had no problems with this saw.
This is a first class, well engineered, well built saw. All the critical adjustments (blade vertical, parallel to mitre slot, fence parallel to blade, etc) were dead-on right out of the box. I installed a Freud thin kerf blade with stabilizing plate (highly recommend a thin kerf blade). I bought the side and back extensions which greatly increase the usability of the saw. Even though the miter slot is a T-slot, it accepts 3rd party accessories.
The stand is a beautifully engineered device. I don't anticipate taking this around a lot like a contractor, but I sure do like that I can fold it up and stick it in the corner when not in use and gain some space back. I am very impressed and pleased with this saw and easily recommend it.
Permalink Reply by Jeffrey Pike on June 2, 2010 at 3:47pm
I have the the Makita 2703 and the Rousseau stand and it works great the price is about the same the benifit with this set up is it is easy to set up and break down not only that but I cut in a router insert for my router . the fence is a t-fence it always square with the blade. The max ripping is about 30 'maybe little less . For more information goto (rousseau.com)
Permalink Reply by Stanley C. Pearse on June 2, 2010 at 4:47pm
Thanks Phil. I will look into this saw.
One question...how is the dust collection / evacuation working on the saw?
Phil Howard said:
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).
Permalink Reply by Jeffrey Pike on June 2, 2010 at 5:42pm
the dust collection is fine hook it up to the shop vac and go
Stanley C. Pearse said:Thanks Phil. I will look into this saw.
TableOne question...how is the dust collection / evacuation working on the saw?

Bosch Table Saw Mitre Slot

Phil Howard said:
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).
Permalink Reply by Phil Howard on June 3, 2010 at 1:20am
The dust collection is great on it. Also, when you fold the saw/stand into the stored position it only takes up a few square feet of space. From all of the reviews I've read it looks like Ridgid used the Bosch as it's benchmark... they are both very similar.
Stanley C. Pearse said:Thanks Phil. I will look into this saw.
One question...how is the dust collection / evacuation working on the saw?
Phil Howard said:Bosch
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).

Bosch Table Saw Miter Slot Sled

Permalink Reply by Stanley C. Pearse on June 3, 2010 at 9:27am
Thanks again Phil. I stopped by at HD last night on my way home from work and took a gander at it. You are right about the dust collection system...very simular to the Bosch.
I am intrigued about the Lifetime Warranty...have you seen any issues with it? Thinking about it...if Bosch is such a great product why don't they have one on their saw??? Hummmm.....
Phil Howard said:The dust collection is great on it. Also, when you fold the saw/stand into the stored position it only takes up a few square feet of space. From all of the reviews I've read it looks like Ridgid used the Bosch as it's benchmark... they are both very similar.
Stanley C. Pearse said:Thanks Phil. I will look into this saw.
One question...how is the dust collection / evacuation working on the saw?
Phil Howard said:
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).
Permalink Reply by Phil Howard on June 3, 2010 at 12:41pm
Don't get me wrong, the Bosch is a great product but to get a setup similar to the Ridgid you will pay $300-400 more for the Bosch. That's what helped make my decision easier.
Stanley C. Pearse said:Thanks again Phil. I stopped by at HD last night on my way home from work and took a gander at it. You are right about the dust collection system...very simular to the Bosch.
I am intrigued about the Lifetime Warranty...have you seen any issues with it? Thinking about it...if Bosch is such a great product why don't they have one on their saw??? Hummmm.....
Phil Howard said:The dust collection is great on it. Also, when you fold the saw/stand into the stored position it only takes up a few square feet of space. From all of the reviews I've read it looks like Ridgid used the Bosch as it's benchmark... they are both very similar.
Stanley C. Pearse said:Thanks Phil. I will look into this saw.
One question...how is the dust collection / evacuation working on the saw?
Phil Howard said:
Get the Ridgid r4510. It's alot cheaper, on par with the Bosch, better fence and warranty. I bought it 6 months ago and couldn't be happier. Just make sure it's the r4510 and not the ts2410 because they look similar. The r4510 is the latest model with the split blade guard, riving knife, adjustable splitter, better stand and bigger on/off switch. The only downside so far is the dado insert plate is on back order and you'll have to make your own zero clearance throat plate. I got mine for $450 by using a Lowe's 10% off coupon at Home Depot (get a change of address packet at the post office, it'll include the coupon).
  • ‹ Previous
  • 1